Interfacing With Microprocessor A interface to microprocessor. Module 3: I/O programming: I/O addresses MAP of x86 PC’s, programming and . To have more pins for I/O, the is interfaced to – a PPI (Parallel. Microprocessor | (programmable peripheral interface) · Interface with Subtract content of two ports by interfacing with microprocessor first_page program to determine subtraction of corresponding elements of.
| Author: | Kazranos Kesho |
| Country: | Solomon Islands |
| Language: | English (Spanish) |
| Genre: | Life |
| Published (Last): | 11 February 2012 |
| Pages: | 249 |
| PDF File Size: | 12.6 Mb |
| ePub File Size: | 16.60 Mb |
| ISBN: | 149-4-27408-383-6 |
| Downloads: | 11843 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Mooguktilar |
Itnerfacing Forgot your password? In this section we discuss many useful applications like keyboard and display interface, traffic light control, printer interface and so on.
The DAC find applications in areas like Digitally controlled gains Motor speed controls Programmable gain amplifiers etc. Share buttons are a little bit 808.
UNIT-IV 8255 PPI Various Modes Of Operation Interfacing To 8086. The count for rotating the shaft of the stepper motor through a specified angle may be calculated from the no. Assume that the routine for this delay is already available. Address lines A 0 — A 1 are used by for internal decoding. Intel CPU Structure. Interrupt Structure of. The shaft of the stepper motor is connected to the quartz ampoule via proper mechanical coupling arrangement. The stepper motor is interfaced with programmable peripheral interface IC 8255 which is controlled by microprocessor 8085. Suitable instrumentation is developed to drive the stepper motor having step angle of 1.8o. We can change the. SECTION INTERFACING Chapters 12 and 13 detailed real-world the to LCDs, stepper motors, and ADC devices, then program it using. Upon completion of this chapter, you will be able to:» Describe how to expand the I/O ports of the /51 by connecting it to an chip» List the 3 ports of.
CWR address is 86h. To get absolute address, all remaining address lines A 15 — A 2 are used to decode the address for An external feedback resister acts to control the gain.
To use this website, you must agree to our Privacy Policyincluding cookie policy. We think you have liked this presentation. Share buttons are a little bit lower. Auth with social network: Out of these 8 inputs wity one can be selected for conversion by using 3 address lines A,B,C.
An operational amplifier is used as a current — to — voltage converter at the output of AD Intel CPU Structure. Maximum Mode Configuration of Auth with social network: With a pulse applied to the winding input, the rotor rotates by one teeth position or an angle x.
Once solution is similar to – This can be solved in many ways. By loading Read Back command to control register the count – By loading Read Back command to control register the count bits of all selected counters are inerfacing.
This can be solved in many ways. Feedback Privacy Policy Feedback. If you wish to download it, please recommend it to your friends in any social system. The stepper motor has rotor teeth.
About project SlidePlayer Terms of Service.
8255A – Programmable Peripheral Interface
Interrupt Structure of If you wish to download it, please recommend it to your friends in any social system. One less than terminal count- OUT becomes low for one clock pulse. The Pulse width depends on the count value. It employs rotation of its shaft in terms of steps, rather than continuous rotation as in case of AC or DC motors. To use this website, you must agree to our Privacy Policyincluding cookie policy.
To rotate the shaft of the stepper motor, a sequence of pulses is needed to be applied to the windings of the stepper motor, in a proper sequence.
Your email address will not be published. Features of Microprocessor. Features of Programmable Interrupt Controller.
Thus pulses are produced continuously in mode 2 Mode 4 – When count reaches terminal count i. Without disturbing the counting. My presentations Profile Feedback Log out. Explain the mode of operation and initialisation.
The count for rotating the shaft of the stepper motor through a specified angle may be calculated from the no. Thus duration of pulse can be elongated.
Published by Arleen Gray Modified over 2 years ago. Published by Derick Warren Modified over 3 years ago. Modular Programming in Microprocessor.
Mode 5 – Hardware Triggered strobe. Design of Microprocessor-Based Systems Dr. The sequence of pulses can be decided, depending upon the required motion of the shaft. Timers and Counters in Microcontroller.
Supporting Circuits of Ijterfacing.
Intel A Programmable Peripheral Interface
It has inyerfacing 8-bit parallel ports: The angle x may be calculated as: Explain the mode of operation and initialization. Operating Modes of The signal may be used to interrupt the CPU if required. The format of status register is shown. Select your Language English.
In clockwise 5 rotations In anticlockwise 5 rotations.